The Bestem carbon fiber sprocket cover (SKU CBDU-696-SPC) is a direct bolt-on replacement for the stock sprocket cover on every Ducati Monster 796 model year (2010–2014). It is made from 100% pre-preg Toray carbon fiber, autoclave-cured in matched-metal molds, and finished with a proprietary UV-resistant clear coat backed by a lifetime warranty against sun-ray yellowing.
What is the Bestem carbon fiber sprocket cover for the Ducati Monster 796?
It is a cosmetic and protective upgrade that replaces the factory front sprocket (countershaft) cover on the left side of the engine. The part shields the rider from the front sprocket and chain, keeps chain fling and road debris contained, and cleans up the look of the engine cases with a visible carbon weave. Key facts:
- Material: 100% pre-preg Toray carbon fiber — no fiberglass backing, no wet-lay, no carbon-look plastic
- Process: autoclave-cured in matched-metal (metal-molded) tooling for consistent wall thickness and exact mounting-point placement
- Finish: twill weave under a high-gloss, UV-resistant clear coat
- Mounting: uses the factory bolt holes and OEM hardware — no drilling or trimming
- Warranty: lifetime warranty against UV / sun-ray yellowing
Will this sprocket cover fit my Monster 796?
Yes. The cover fits all Ducati Monster 796 model years (2010–2014), including ABS variants. Because Ducati shared this engine-case casting across the air-cooled Monster line, the same part also fits the Monster 696 (2008–2014), Monster 1100 (2009–2010), and Monster 1100 EVO (2011–2013). Fitment is to the factory mounting points, so installation is a straight swap with the stock piece.
Why replace the stock sprocket cover with carbon fiber?
On a small guard like this, the gram savings are modest — that is not the real reason to upgrade. The practical gains are:
- Durability: pre-preg carbon does not corrode, chip, or rust the way painted metal covers do, and it tolerates chain lube and road grime without staining
- Consistency: matched-metal molds mean the bolt holes land where Ducati put them — no fighting misaligned aftermarket parts
- Appearance: a twill carbon weave ties the engine area together, especially if you are already running other carbon pieces on the bike
How is Bestem carbon fiber made?
Every Bestem part starts as 100% pre-preg Toray carbon fiber — fabric pre-impregnated with a measured resin content, the same material class used in aerospace structures. Parts are laid into matched-metal molds and cured in an autoclave under heat and pressure, which compresses the laminate, drives out voids, and produces a stronger, lighter, more consistent part than hand-laid or wet-lay methods. This is the same autoclave plus 100% pre-preg construction that premium European carbon makers such as Ilmberger built their reputation on — Bestem uses that same technology and adds a superior UV-resistant coating on top of it.
Do carbon fiber sprocket covers turn yellow in the sun?
They can — sun-ray (UV) yellowing is the most common defect riders see on carbon fiber parts, because standard clear coats begin to amber and cloud after roughly 1,000 hours of UV exposure. Bestem's proprietary UV-resistant coating is rated to approximately 3,000 hours of UV resistance — about three times longer than standard OEM clear coat before yellowing appears. Because of that coating, this sprocket cover carries a lifetime warranty against sun-ray (UV) yellowing.
How do you install a sprocket cover on a Monster 796?
Plan on about 10 minutes with basic hand tools:
- Remove the bolts holding the stock sprocket cover and lift it away from the engine case
- Wipe chain residue off the mounting face so the new cover seats flat
- Position the carbon cover and reinstall the OEM hardware by hand first to confirm alignment
- Snug the bolts evenly — do not over-torque fasteners into carbon fiber
No drilling, trimming, or sealant is required.
What other carbon fiber parts fit the Monster 796?
If you are building out the bike, these pieces share the same construction and UV coating and fit the Monster 796:
Why buy from Bestem USA?
Bestem has been manufacturing carbon fiber since 2005 — more than 20 years — and supplies OEM carbon fiber parts to car and motorcycle manufacturers, not just the aftermarket. All parts are stocked in our Atlanta, GA warehouse and ship daily worldwide, and live phone support is available every business day if you have a fitment question before you order.
FAQ
Does the Bestem sprocket cover fit the Monster 796 ABS?
Yes. The cover mounts to the engine case, which is unchanged on ABS models, so it fits all Monster 796 trims and model years from 2010 through 2014.
Is this real carbon fiber or carbon-look plastic?
It is 100% pre-preg Toray carbon fiber, autoclave-cured in metal molds — not hydro-dipped or wrapped plastic, and not a fiberglass part with a single carbon skin layer.
Will the clear coat yellow over time?
Bestem's proprietary UV-resistant coating is rated to roughly 3,000 hours of UV exposure versus about 1,000 hours for standard OEM clear coat, and the part carries a lifetime warranty against sun-ray (UV) yellowing.
Do I need any special tools or modifications to install it?
No. It bolts to the factory mounting points using the OEM hardware. Installation takes about 10 minutes with basic hand tools.
Is the Monster 796 sprocket cover in stock?
Yes. It is stocked in Bestem's Atlanta, GA warehouse and ships daily, worldwide.